2025-01876CITY OF MONTICELLO
505 WALNUT STREET
MONTICELLO, MN 55362-
63) 295-3060 YAX: (763) 295-4404
ADDRESS : 9320 CEDAR ST S
PIN : 155207001010
LEGAL DESC : MONTICELLO BUSINESS CTR 3RD ADDN
LOT 001 BLOCK 001
PERMIT TYPE : FIRE SAFETY
PROPERTY TYPE : COMMERCIAL
CONSTRUCTION TYPE : FIRE ALARM SYSTEM
VALUATION : $ 20,000.00
NOTE: INSTALL NEW ALARM COMBO PANEL.
REPLACE 2 NEW KEYPADS.
NEW HORN STROBE IN HEALTH SERVICE ROOM.
REPLACING CEILING TILES.
INSTALL NEW STROBE IN PERSONNEL ROOM.
INSTALL STROBE IN REAR ALCOVE.
INSTALL NEW STROBES IN PICK UP STORAGE.
RELOCATE TWO EXISTING NOTIFICATION DEVICES IN SALES.
MAKE FINAL CX CONNECTIONS, AND ADD SYNC MODULE TO NEW FIRE PANEL.
liiiiiiiiiiiiiiiiiiiiillillillillilligim
2 0 2 5— 0 1 8 7 6*
DATE ISSUED: 12/22/2025
Permit #: 2025-01876
APPLICANT FIRE SUPPRESSION FEE 340.53
PLAN REVIEW - FIRE 221.34
WACHTER INC
STATE SURCHARGE, OTHER VAL 10.00
16001 WEST 99TH STREET
KS 66219- TOTAL 571.87LENEXA,
Payment(s) 479) 757-8286
CHECK 355825 571.87
OWNER
WAL-MART REAL EST BUSINESS TR
1301 1OTH ST SE
PROP TAX DEPT #8013
AR 72716-0555
AGREEMENT AND SWORN STATEMENT
I agree that the work will be conducted in conformance with
the ordinances of the City of Monticello and with the
Minnesota State Building Code. I understand that the work
will be in accordance with the plan that has been approved
by the Building Official. I agree that any damage caused to
public property including but not limited to curb, sidewalk,
public utilities and signs will be repaired at my expense.
Applicant
Date
Bldg Official Date
SEPARATE PERMITS REQUIRED FOR WORK OTHER THAN DESCRIBED ABOVE.
O
FIRE DEP.T.
FIRE PROTECTION/ALARM PERMIT APPLICATION
103 CHELSEA ROAD MONTICELLO, MN 55362 PHONE: 763-295-3060
E (D L" 0 V
za ID i
Project Address: 9320 CEDAR ST Monticello, MN 55362
Lot Block Development
Legal 001 001
Owner WAL-MART REAL EST BUSINESS TR I Telephone E-Mail Address
4797578286 onlinepermits@wachter.com
Contractor License Number E-Mail Address
Wachter, Inc./Jared Botteron EA003725 online permits@wachter.com
Mailing Address
16001 W 99th St. Lenexa, KS 66219
Contact Person Telephone Mobile Telephone
Katy Savage 4797578286
Property Single Family Two -Family Multifamily Townhome Agricultural
Type Residential Residential Residential
iCHECK ONE) 0 Commercial Industrial Institutional Public / Gov't OTHER
Fire Protection Permit Type Project Valuation
Fire Wet Sprinklers # of Heads
Suppression
System ElDry Sprinklers - Pressurized # of Heads $
Chemical, Ansul / Comm Kitchen - OTHER # of Heads
Fire Suppression Monitoring System $
Fire Alarm
System ® Building Fire Alarm System 20,000.00
Install new alarm combo panel. Replace 2 new keypads. New horn strobe in health service room. Replace ceiling tiles.
Instali new strobe in personnel room. Install strobe in rear alcove. Insta'I new strobes in pick up storage. Relocate two exist -
Description ing notification devices in sales. Make final CX connections, and add sync module to new fire panel.
of work:
OTHER FIRE PROTECTION SYSTEM (Specify Type & Number)
Si ure of ire Protection Contractor Date
Signaturp of Owner (If Owner t.s Buddor) Date
c
I hereby apply for a fire protection permit and acknowledge: the information above is complete and accurate; the work will be in conformance with the ordinances or,d codes of the
City of Monticello and lL1innesoto State Building and Fire Codes; I understand this is not a permit but only an application for permit; work is not to start without permit; work will be
in accordance with the Approved Plan when City plan approval required. This application and any issued permit may become null and void if permit is not issued or work is not
commenced within 180 days, or if work is suspended or abandoned for a period of 180 days I hereby certify that 1 have read and examined this application the granting of a permit
does not presume to give authority to violate or cancel the provisions of any rher state or local low regu!oting construction or the performance of construction.
B - VQR CtTYaE LY
PLAN CHECK REQUIRED Plans Checked By Iykl 65% of Permit Fee
Approved for Issuance Date _
Fire Protection Permit Fees
Project Valuation to be used in computing permit fee is the fair market value of work, including
the total costs of materials, labor, profit and overhead for which the permit is issued.
Minimum Permit Fee (All Permit T)pes) 100.00
Fire Suppression System 1.25% of Project Valuation
Fire Alarm System 1.25% of Project Valuation
Commercial Fuel Storage Tank 1.25% of Project Valuation
Other Fire Protection System 1.25% of Project Valuation
Plan Review Fee (Charged For All Permit Types When Plans Must Be Submitted) 65% of Permit Fee
Minnesota State Surcharge must be charged
in addition to permit fees for all permit types: 0005 x Project Valuation
DO NOT SEND A CHECK WITH YOUR APPLICATION
All submissions must be electronic and include the following:
Application
Plans
Spec sheets
Email electronic files to Eire.Marshal@MonticelloMN.gov
FIRE ALARM PRODUCT DATA
WALMART STORE #3624
9320 CEDAR ST
MONTICELLO, MN 55362
4ont cell
il•i D!hG $4fETY
APPROVED FILE Cl1PY
REVIEWED FOR COnE C0".7PLIANCE
YCT TO FIELD IN'SPFCTION
Cat:.•__" ! 7
Signature:
Jason M. Scates, P.E.
1805 N. 2°d Street
Rogers, AR 72756
The product data sheets included herein are for reference to indicate the specific products and
materials that were included in the Fire Alarm design for this project. These products and materials
are being provided as work products of other entities. The Engineer of Record for the Fire Alarm
design project ( Jason M. Scates, P.E. ) does not intend to portray any responsibility for these products
other than to specify them as finished products and materials for inclusion as components in the Fire
Alarm design.
www.boschsecurity.com (
4L BOSCH
Invented for life
The B9512G Control Panel and the B8512G Control
Panel are the new premier commercial control panels
from Bosch. B9512G control panels integrate
intrusion, fire, and access control providing one simple
user interface for all systems.
With the ability to adapt to large and small
applications, the B9512G provides up to 599
individually identified points that can be split into 32
areas.
The control panel can communicate through it's built-
in Ethernet port (not applicable to "E" control panels),
or through compatible plug-in modules that can send
events over the public switched telephone network
PSTN) or over cellular network communications.
Fully integrated intrusion, fire, and access control
allows users to interface with one system instead of
three
Provides up to 599 points using a combination of
hardwired or wireless devices for installation
flexibility, and up to 32 areas and 32 doors for up to
2,000 users
On -board Ethernet port for Conettix IP alarm
communication and remote programming,
compatible with modern IP networks including IPv6/
IPv4, AutolP, and Universal Plug and Play
Installer -friendly features including onboard USB
for easy on -site RPS programming, plus support for
Remote Connect Service and plug-in PSTN and
cellular communication modules for simple
installation and communications
Remote Security Control (RSC) app which allows
users to control their security systems - and view
system cameras - remotely from mobile devices
such as phones and tablets
For users, programmable keypad shortcuts, situation
sensitive on -screen help, and a bilingual user interface
make system operation simple and easy.
With the B9512G Control Panel, you can:
Monitor alarm points for intruder, gas, or fire alarms.
Program all system functions local or remote using
Remote Programming Software (RPS) or by using
basic programming through the keypad.
Add up to 32 doors of access control using the
optional B901 Access Control Module. (Optionally use
the D9210C Access Control Interface Module for up
to eight of the 32 doors.)
The B9512G is a direct replacement for previous
control panel models D9412GV4, D9412GV3,
D9412GV2, and D9412G.
www.boschsecurity.com
C"J BOSCH
Invented for life
The B926F Fire Keypad is a fully supervised SD12
device for fire applications.
Each keypad has user -adjustable backlit keys, a display
that shows system messages, and a sounder. The
sounder emits distinct condition tones to alert you to
a fire alarm, a fire trouble, or fire supervisory events as
they occur. The keypad includes fire status indicators
and fire function keys.
LCD display
The keypad uses words, numbers, and symbols to
show the status of the security system. When several
events occur, the keypad shows each event in order of
priority.
Keys
Each keypad has 10 number keys and 5 navigation
keys.
When pressed, keys turn on keypad backlighting and
emit the keypress tone (short beep). The keypad has 4
Fire function keys:
ACK. Press to acknowledge the system alarm or
trouble condition.
SILENCE. Press to silence fire alarms or troubles.
Fire keypad with fire function keys: ACK, SILENCE,
RESET, and DRILL
2-line LCD display with up to 32 character point,
user, and area names
Simple menu -style user interface with dedicated
function buttons for common commands, including
status indication
Quickly identifiable, visual indicators for critical
system statuses
Simple installation with self-locking base and
chassis design, plus built-in bubble level
RESET. Press to reset devices such as smoke
detectors, and clear restored points.
DRILL. Press and hold to initiate a fire drill.
Audible tones
The keypad has a built-in sounder that produces
several distinct warning tones. The tones are
differentiated so that the user can recognize an event
simply by hearing its associated tone.
Status indicators
The status indicators on the keypad provide a quick
visual reference for system status.
The indicator lights when the system is ready to turn on (arm).
The indicator lights when the system is on (armed).
The indicator lights when dangerous gases are present
including carbon monoxide (NFPA 720).
The indicator lights when the system has power.
AL1002ULADAffl: Altrom x NAC Power Extenders
Overview
Rev. AL 1002ULADA )3102015
AL 1002ULADA are extremely cost effective voltage regulated remote NAC
Power Extenders. They may be connected to any 24 volt Fire Alarm Control
Panel (FACP). Primary applications include Notification Appliance Circuit
NAC) expansion (supports ADA requirements) and providing auxiliary power
to support system accessories.
S_ pecifii
Input:
Power input 120VAC 60 Hz, 5 amp.
Two (2) Class A, Style Z or two (2) Class B,
Style W, Y FACP inputs.
Two (2) NC dry contact trigger inputs.
Output:
Class 2 Rated power -limited outputs.
24VDC @10 amp max total alarm current.
2.5 amp max current per output.
Separate 1.0 amp auxiliary output.
Programmable supervised indicating circuit outputs:
Four (4) Class B, Style W, Y or Two (2) Class A,
Style Z or One (1) Class A, Style Z and Two (2)
Class B, Style W, Y.
Thermal and short circuit protection with auto reset.
Battery Backup:
Built-in charger for sealed lead acid or gel type batteries.
Automatic switchover to stand-by battery when
AC Fails.
Zero voltage drop when switching over to
battery backup.
Supervision:
AC fail supervision (form "C" contact, 1 amp / 28VDC).
Factory set for 30 seconds with optional 2.5 to 3 hour
delay setting (field selectable).
Instant local AC trouble reporting relay
form "C" contact, 1 amp / 28VDC).
Battery presence and low battery supervision
form "C" contact, 1 amp / 28VDC).
rations
Visual Indicators:
Input and output status LED indicators.
Special Features:
2-wire horn/strobe Sync mode allows audible
notification appliances (horns) to be silenced
while visual notification appliances (strobes)
continue to operate.
Sync protocols include Potter/Amseco, Faraday,
Gentexg, System Sensors, and CooperWheelockg.
Temporal Code 3, Steady Mode, Input to Output
Follower Mode (maintains synchronization of
notification appliances circuit).
Compatible with 12VDC or 24VDC fire panels.
Output loop supervision steered to input l or input 2.
Signal circuit trouble memory (helps identify
intermittent loop problems).
Common trouble input and output.
Ground fault detection.
Unit includes power supply, red enclosure, cam lock,
and battery leads.
Mechanical:
Enclosure Dimensions (H x W x D approx.):
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)
Product weight (approx.): 12 lbs. (5.44 kg).
Shipping weight (approx.): 13.3 lbs. (6.03 kg).
Agency Approvals
UL Listed Control Units and Accessories California State Fire Marshal Approved. U` for Fire Alarm Systems (UL 864) Ninth 'IC•'
Edition
VIC
M EA NYC Department of Buildings Approved
Approved
FM Factory Mutual Approved.
APPROVED
www.boschsecurity.com Cl BOSCH
Invented for life
B96 Keypad Trim Bezel
Cover the wall footprint of previous keypads when
replacing them with the new, slim design of B Series
keypads. The white trim bezel is 8.6 in x 6.3 in x 0.12
in (22 mm x 16 mm x 3 mm).
Order number B96
www.boschsecurity.com OWF- BOSCH
Invented for life
l
11111 P-1,
r
1
The D273 Family includes the following detector
models:
Model Description
D273 Four -wire
D2731S ! Four -wire with an isolated 135'F (57'C) heat sensor
and sounder
D273TH Four -wire with 135'F (57'C) heat sensor
D273THC Four -wire with 135'F (57'C) heat sensor and auxiliary
relay
D273THCS' Four -wire with 135'F (57'C) heat sensor, auxiliary
relay, and sounder
D273THE Four -wire with 135'F (57'C) heat sensor and EOL
relay
D273THR2 Four -wire with 135'F (57'C) heat sensor and trouble
relay
D273THS! Four -wire with 135'F (57'C) heat sensor and sounder
D273THES= Four -wire with 135'F (57'C) heat sensor, sounder,
and EOL relay
12 VDC or 24 VDC input
Designed for commercial or residential use
Four -wire application
Light -emitting diodes (LEDs) indicate the status of
the chamber, power, and alarm
Removable terminal block to simplify wiring
connections
Sounders produce 85 dB at 10 ft (3 m)
The trouble relay indicates both Dirty Smoke Chamber and/or
Power Loss conditions.
Each of the detector models is UL Listed and works
with commercial fire protective signaling and
household fire warning systems. Each model detects
smoke particles produced during wood, paper, and
fabric combustion.
These detector models use an infrared (IR) LED light
source and a silicon photodiode to measure light in a
chamber. A fine screen covers the chamber to deter
insects and reduce dust accumulation and nuisance
alarms.
During a fire, smoke particles reflect light onto the
photodiode. When the photodiode measurements
exceed the alarm threshold, the detector signals an
alarm condition. After the alarm condition clears,
interrupt power at the control panel to reset the
detector.
www.boschsecurity.com
BOSCH
Invented for life
The FMM-100 family are versatile, high -quality, metal
fire alarm manual stations. Single-action or dual -action
models are available. All models come with a key lock
and contain gold-plated contacts to resist corrosion.
Operation
Single-action
When the bar on the front of the manual station is
pulled, it latches open and is easily visible from 50 ft
15 m). Reset the activation bar by opening the
manual station with the key and placing the activation
bar in its normal upright position. An optional scored
acrylic break rod is available.
Dual -action
With the dual -action configuration the upper bar on
the front of the manual station rotates inward allowing
the activation bar to be grasped and operated by a
single hand.
Single or dual action
P. Terminal connections
Gold-plated alarm contacts for corrosion resistance
Surface or weatherproof back boxes
Certifications and approvals
Region Certification
USA UL UNIU: Boxes, Non -Coded (UL38),
UNIU7: Boxes, Non -Coded Certified for
Canada (cULus)
CSFM see our website
NYC- 382-94-E, Vol. VI
MEA
Compatibility Information
These manual stations are compatible with all Bosch
Security Systems, Inc. Fire Alarm Control Panels.
Mounting Considerations
These manual stations can be surface mounted on
either the FMM-100BB-R Surface -mount Back Box or
the FMM-100WPBB-R Weatherproof Back Box. They
can also be flush mounted on a standard single -gang
back box.
SYSTEM
SENSOR
LmSeries and
LoSeries with LED
Indoor Selectable
Horns, Strobes and
Horn Strobes
System Sensor L-Series and L-Series with LED audible
visible notification products are rich with features
guaranteed to cut installation times and maximize profits
with lower current draw and modern aesthetics.
Features
LED technology provides lower current draw
Digital Voltage Meter (DVM) diagnostic test points for Horn
Strobes and Strobes
Common aesthetics across the L-Series platform
Standard and compact sizes
Tamper -resistant construction
Field -selectable candela settings on wall units: 15, 30, 75, 95,
110, 135, and 185
Field -selectable candela settings on ceiling units: 15, 30, 75, 95,
115, 150, and 177
Rotary switches for candela, tone and volume selections
Mounting plate provides plug-in design for easier installation and
shorting springs to check wiring continuity
Electrically compatible with legacy SpectrAlert, SpectrAlert
Advance and L-series devices
Synchronization through use of UL approved power supplies that
support System Sensor Sync protocol or System Sensor MDL3
Sync Module
Horns, Strobes and Horn Strobes listed for wall or ceiling use
Agency Listings
5Xkk AC SIGNALING
c@us U< o FM
USTEO MCn fin
APPROVED
Horn Strobes Horns: horns: 3057072 7300-16530525
and Strobes: S4011 S4011 rM23FPUSG195 7135-1653-05M
S5512. S4011 7135-1653:0526
The System Sensor L-Series and L-Series with LED
platform offers the most versatile and easy -to -use line of horns,
strobes, and horn strobes in the industry with lower current draw and
modern aesthetics. LED lighting technology offers significantly lower
current draw compared to older Xenon bulbs across a full candela
range. This improves design flexibility for notification appliance
circuits (NACs) while also reducing power supply requirements
allowing for simpler and lower cost installations.
Flexible design options meet virtually any application requirement:
wall or ceiling mount, standard or compact sizes, red or white color
choices, bezel kits for alternate markings and languages, and LED
color lenses for distinctive visual signaling. In addition, installers can
easily adapt devices using field selectable candela, tone and volume
settings using rotary switches.
The L-Series and L-Series with LED line is developed to simplify
installation. All devices feature plug-in designs with minimal intrusion
into the back box, making installations fast and foolproof while
virtually eliminating costly and time-consuming ground faults. The
universal mounting plate includes an onboard shorting spring, so
installers can test wiring continuity before the device is installed.
In addition, the System Sensor L-Series with LED notification
appliances offer a new diagnostic test point feature that allows you
to measure device voltage with a digital voltage meter (DVM) without
removing the appliance from the wall or ceiling. The DVM test points
are discreetly located on the face of the notification appliance which
enable faster troubleshooting and end of line (EOL) voltage checks
while greatly reducing the risk of misplacing or damaging appliances
during troubleshooting.
AVDS916-01 - 10/03/2023 - Gage 1
SYSTEM SENSOR
Indoor
Selectable - Output
Strobes and Horn
Strobes for Ceiling
Applications SpectrAlert@
Advance audible visible notification products are
rich with features guaranteed to cut installation times and
maximize profits. Features
Plug-
in design with minimal intrusion into the back box Tamper -
resistant construction Automatic
selection of 12- or 24-volt operation at 15 and 15/
75 candela Field -
selectable candela settings on ceiling units: 15, 15/75, 30, 75,
95, 110, 115, 135, 150, 177, and 185 Horn
rated at 88+ dBA at 16 volts Rotary
switch for horn tone and three volume selections Universal
mounting plate for ceiling units Mounting
plate shorting spring feature checks wiring continuity before
device installation Electrically
Compatible with legacy SpectrAlert devices Compatible
with MDL3 sync module Listed
for ceiling or wall mounting Agency
Listings SIGNauNs
W
LISTED
van approved 71225-1 ai88 (horn strobes,
s,
S4011 (
ch:rnes, horn strobes, tams) 3023572 YEA452-05-E chine strobes) S5512 (
strobes) 7135-1653 0189 (horns, chimes) W
S_ _y s t e m S e n s o The
SpectrAlert Advance series offers the most versatile and easy -
to -use line of horns, strobes, and horn strobes in the industry. With
white and red plastic housings, wall and ceiling mounting options,
and plain and FIRE -printed devices, SpectrAlert Advance can
meet virtually any application requirement. Like
the entire SpectrAlert Advance product line, ceiling -mount strobes
and horn strobes include a variety of features that increase their
application versatility while simplifying installation. All devices feature
a plug-in design with minimal intrusion into the back box, making
installations fast and foolproof while virtually eliminating costly
and time-consuming ground faults. To
further simplify installation, SpectrAlert Advance utilizes a universal
mounting plate so you can mount them to a wide array of
back boxes. With an onboard shorting spring, installers can test wiring
continuity before the device is installed. Installers
can also easily adapt devices to a suit a wide range of application
requirements using field -selectable candela settings, automatic
selection of 12- or 24-volt operation, and a rotary switch for
horn tones with three volume selections.
SYSTEM
SENSOR
Outdoor Selectable -
Output Horns,
Strobes, and
Horn Strobes for
Wall Applications
SpectrAlert® Advance outdoor audible visible products
are rich with features that cut installation times and
maximize profits.
Features
Weatherproof per NEMA 4X, IP56
Listed to UL 1638 (strobe) and UL 464 (horn)
Compatible with System Sensor synchronization protocol and
legacy SpectrAlert products
Field -selectable candela settings: 15, 15/75, 30, 75, 95, 110, 115,
135, 150, 177, and 185
Automatic selection of 12- or 24-volt operation at 15 and
15/75 candela
Rotary switch for horn tone and three volume selections
Horn rated at 88+ dBA at 16 volts
Rated from -40OF to 151 OF
Universal mounting plate with an onboard shorting spring that
tests wiring continuity before devices are installed
Plug-in design with minimal intrusion into the back box
Tamper -resistant construction
Listed for ceiling or wall mounting
Agency Listings
SIGNALING
L13TED i M
S4011 (chtrnes horn strobes, horns) APPROVED
S3593 (outdoor and aler, strobes) 302 1-
NEA7300-1653 187 (outdoor sWobes)
approved 1251ss3,8gc )
MEA452-05-E 71351653 189 (horns, chines)
SPECTRA.-W-kWrt
f r o m S s t e m S e n s o
SpectrAlert Advance offers the broadest line of outdoor horns,
strobes, and horn strobes in the industry. With white or red plastic
housings, wall or ceiling mounting options, and plain or FIRE -printed
devices, SpectrAlert Advance can meet virtually any application
requirement, including indoor, outdoor, wet, and dry applications in
temperatures from -40OF to 151 OF.
Like the entire SpectrAlert Advance line, outdoor horns, strobes,
and horn strobes for wall applications include a variety of features
that increase application flexibility and simplify installation. First,
field -selectable settings, including candela, automatic selection of
12- or 24-volt operation, horn tones, and three volume options enable
installers to easily adapt devices to meet requirements.
Next, SpectrAlert Advance devices use a universal mounting plate
for both wall and ceiling applications. This mounting plate includes
an onboard shorting spring that ensures wiring continuity before
devices are installed, so installers can verify proper wiring without
mounting the devices and exposing them to potential construction
damage. Once the plates are mounted, all SpectrAlert Advance
devices utilize a plug-in design with a single captured screw to
speed installation and virtually eliminate costly ground faults.
Outdoor devices ship with weatherproof plastic back boxes (metal
back boxes are available separately) that accommodate in -and -
out wiring for daisy chaining devices. Plastic back boxes feature
removable side flanges and improved resistance to saltwater
corrosion. Knock -outs located on the back eliminate the need to drill
holes for screw -in mounting. Plastic and metal weatherproof back
boxes come with 3/4-inch top and bottom conduit entries and 3/4-inch
knock -outs at the back. A screw -in NPT plug with an O-ring gasket
for a watertight seal is included with each back box.
www.boschsecurity.com (
4 BOSCH
Invented for life
This module is used for wiring connections to remote
signaling devices. You can connect up to twelve
D192G modules to the same system on compatible
control panels. Wiring is supervised for open, short, or
grounded circuit faults.
The module powers notification appliances from the
control panel power supply or from an Underwriters
Laboratories, Inc. (UL 1481) Listed auxiliary 12 VDC or
24 VDC regulated/power-limited power supply for fire
protective signaling units and commercial/residential
burglar units. This feature allows the system to
support more signaling devices on longer wire runs. It
also allows the use of 12 V or 24 V notification
appliances requiring the appropriate power supply.
Supervises 12 VDC or 24 VDC NACs
The D192G powers the notification devices from either
the control panel's power supply or from a UL Listed
Auxiliary 12 VDC or 24 VDC regulated power -limited
power supply for use with Fire Protective Signaling
Units and Commercial and Residential Burglar Units.
The choice of power supply allows the use of 12 V or
24 V notification devices.
is. Supervises 12 VDC or 24 VDC notification appliance
circuits (NACs)
Supervised signal silencing switch
P. Notification appliance circuit rated at 3.0 A
P. Multiple module configurations
Mounts in panel enclosure
Supervised Signal Silencing Switch
The D192G module has a toggle switch for silencing
the notification devices while testing the alarm panel.
When this toggle switch is in the Silence (Off)
position, the module indicates a supervisory trouble
condition to the control panel.
Multiple Module Configurations
Several modules can be connected to the same zone
or point on the control panel. If individual
annunciation of a notification appliance circuit is
desired, D192G modules can be connected to
separate zones or points on -board or through the
D8128D OctoPOPIT Eight -point Expander.
Mounts in Panel Enclosure
The D192G mounts inside the control panel enclosure
using existing mounting holes or with a D137 or D138
Mounting Bracket. Refer to the control panel's
installation guide for more information on mounting.
www.boschsecurity.com i
BOSCH
Invented for life
Provides point identification for up to 100
connected addressable initiating devices using
POPITs
Supervises wiring to devices for circuit integrity
Expands the number of points in the system
Compact size
Interconnect wiring connectors for easy installation
The B299 POPEX Module is an SD12 compatible Region Certification
device. The module communicates to the control panel
over the SD12 bus, and provides support for up to 100 UL UL 1610 - Central Station Burglar Alarm
POPIT (Point Of Protection Input Transponder)
Units
devices. This occurs over a single expansion loop using UL UL 1635 - Standard for Digital Alarm
two pairs of terminals. Communicator System Units
UL UL 294 - Standard for Access Control
System overview Units and Systems
Each module installs in the control panel enclosure or UL UL 365 - Police Station Connected Bur-
in an adjacent approved enclosure. Future system glar Alarm Units
expansion is very economical as the module supports UL UL 609 - Standard for Local Burglar
zone expansion through supporting D9127U/T POPIT Alarm Units and Systems
modules and POPIT'ed detectors. The POPIT modules
UL UL 636 - Holdup Alarm Units and Sys -
can be placed anywhere along the two -wire data tems
expansion loop from the module.
UL UL 864 -Standard for Control Units and
Certifications and approvals Accessories for Fire Alarm Systems
UL UL 985 - Household Fire Warning Sys -
Region Certification tem Units
USA ANSI- CP-01-2010-Control Panel Standard - CSFM California Office of The State Fire Mar-
SIA Features for False Alarm Reduction shall
UL FCC Part 15 Class B
UL UL 1023 - Household Burglar Alarm Sys- Canada ULC
tem Units
ULC CAN/ULC S303 - Local Burglar Alarm
UL UL 1076 - Proprietary Burglar Alarm Units and Systems
Units and Systems
www.boschsecurity.com
C4 BOSCH
Invented for life
The D9127 Series POPIT Modules includes the D9127T
with magnetic tamper switch) and the D9127U
without tamper). They are used with a D8125
Addressable Expansion Module when there is a need
to expand a compatible control panel beyond its
standard number of on -board initiating zones or
points. Future system expansion is very economical as
D9127 Series POPITs can be added anywhere along
the two -wire data expansion loop from the D8125
module.
Both modules include proven technology that
combines zone and point supervision with individual
device addressing on one pair of wires. Screw
terminals provide reliable connections for the data
expansion loop and supervised sensor loop wiring.
Install a 33 kO end -of -line resistor at the farthest point
on the loop for proper supervision. The units are small
and easily installed in standard outlet boxes, above
false ceilings, closets, or other accessible locations.
Provides point identification of initiating devices
Supervises wiring to devices for circuit integrity
Expands the number of points in the system
P. Compact size
Terminal connections for reliability
Certifications and approvals
Rogion Certification
USA UL
UL UL 365 - Police Station Connected Bur-
glar Alarm Units
UL UL 464 - Standard for Audible Signal Ap-
pliances
UL UL 609 - Standard for Local Burglar
Alarm Units and Systems
UL UL 864 - Standard for Control Units and
Accessories for Fire Alarm Systems
UL UL 985 - Household Fire Warning Sys-
tem Units
UL UL 1023 - Household Burglar Alarm Sys-
tem Units
UL UL 1076 - Proprietary Burglar Alarm
Units and Systems
UL UL 1610 - Central Station Burglar Alarm
Units
UL UL 1635 - Standard for Digital Alarm
Communicator System Units
FM
www.boschsecurity.com i
BOSCH
Invented for life
The D130 Auxiliary Relay Module can be used with all
Bosch Security Systems control panels. The relay
module consists of a 12 VDC or 24 VDC relay. This
device allows the system to handle larger amounts of
current or different voltages that are beyond the
control panel's auxiliary power rating, or the rating of
modules such as the D8129 OctoRelay.
Notice
A UL Listed, 12 VDC or 24 VDC auxiliary power
supply is required to supply power to the D130's
coil.
The relay is polarized and has two sets of non -latching
Form C contacts. When the contacts are in the inactive
state, the normally -closed terminal has continuity with
the common terminal. When the contacts are in the
active state, the normally -open terminal has continuity
with the common terminal. The relay is activated by
switching polarity. A red LED lights to indicate the coil
is energized.
12 VDC or 24 VDC relay
Allows switching of current or voltage
Two non -latching Form C dry contact outputs
Red LED shows coil is energized
Mounts in control panel enclosure
Initiating Circuit Application
The D130 is commonly used with a D125B Dual Class
B Initiating Module and a UL Listed 24 VDC power
supply. In this configuration power to the detectors
can be interrupted by a command from the fire alarm
control panel (FACP).
Region Certification
USA UL APOU: Proprietary Alarm Units
UL1076), UOJZ: Control Units, System
UL864, 9th edition)
FM
CSFM 7167-1615: 100 and 7165-1615: 119
NYC- 12-92-E, Vol. II 12-92-E, Vol. II
MEA
NYC- 12-92-E, Vol. 12 12-92-E, Vol. 12
MEA
NYC- 12-92-E, Vol. 15 12-92-E, Vol. 15
MEA
www.boschsecurity.com (OD BOSCH
Invented for life
The D8130 Door Release Module is an accessory for
fire alarm control panels (FACPs) that controls system
functions commonly required in National Fire
Prevention Association (NFPA) 72 fire alarm
installations. Two independent Form C dry contacts,
each rated at 5 A, connect low -voltage circuits to
magnetic door holders, pilot relays, or contactor units
for function control.
Typical applications are:
releasing fire doors, emergency exit doors, and
stairwell doors
elevator recall
HVAC control
Contact Activation
The control panel indicating output activates the
contacts of the D8130. A red Alarm Input LED
indicates contact activation.
The duration of the contact activation follows the
programmed indicating circuit time. Use a jumper to
set the contact activation to be instant or delayed by
14 sec when there is an alarm condition. With the
delay option selected, a 14 sec delay also occurs upon
restoral. This delay feature is useful for momentary
bell tests.
Two Form C (5 A rated) contacts
Remotely controls fire system devices
Instant or delayed relay activation and restoral
Relay closure follows indicating circuit duration
Disable switch supervised for system testing
If the user silences the alarm output, the D8130
contacts deactivate. Latching features must be
provided for pilot relays or contactor units requiring
control beyond the programmed indicating device time
or after manual silencing of the indicating circuits.
Supervised Disable Switch
To facilitate fire alarm installation testing, the D8130
Module contains a supervised disable switch that
prevents operation of the relay contacts. An amber
Disable LED indicates when the switch is in the
disable position. Connect one or more D8130 modules
to any unused 1 kO zone or point of the control panel
to detect module disabling.
A trouble is indicated when the D8130 switch is in the
disable position, and a restoral signal is sent when the
switch is returned to the normal position. (Refer to the
control panel's Program Entry Guide for details on
programming a trouble signal for an open or short
condition.) When the contacts are activated with the
switch in the normal position, no trouble indications
are sent to the control panel.
Release Contact Outputs
A normally -open (NO) terminal, a normally -closed (NC)
terminal, and a common (COM) terminal are provided
for each D8130 contact. In the inactive state of the
contact, the NC terminal has continuity with the COM
terminal. In the active state of the contact, the NO
terminal has continuity with the COM terminal.
z n
oC QrD o v m o SI fl <
T r c z S = rri rb
N D D (D Q o p ot O n
f1 n rD :3 N
p O
Ln
CD
rD LA00ooon
Lnrr O N 6 Q O O f p •
O M < v
0
Q f
rD
CD-CrD = in 33 rp Ln N •
kInD
N (D fp yfl,
w rD
rD fl
vi a, 3
co
N rD
n o 3 m
M. o 0ort. l< N.
rD o a- -Z3
o °
ro O
fDn
YJ rD
rD
C) ul
QL
ro
N O -p
o< o o •p o
Q
S
O•p < :3n a,
0 n 1p
rD — rD n = D
rD -. rD rDA (D Ln
Un
n " n O0 o 0OQOrrN' v W
rD (D -0 l 3 LT r) o-
n-r n n 00 _ < aF '. rD o D=
VOO ^ O D. n
T
X.
D 0) D N. rD 1p TV
rD OD O rD O< Q rD Q
1 v1V1rY : rD 1 n m , (D'
D O rD (D D-. r 3' o rD o to t '
D rD rD Q rD rD
Ln
Q O < O— cu _Q -r r* Q n n . ,--, D- O ' O
a, ' N, w (
l rD
D o" w n . O
o n,
D-
0 c: n 0 0 o
rt 3 3 n * _*' Lo rD n,
in O r
c o
Q
n 3 d
S. -4, SQO30 fl,
p v C rD D
rD N 3 rD N N n rD 1
rD l/)
rD (D Q o :3 r r rD
Q Q 6 Q 0 n
rD rD D n rD n -OrDvZ) l0
rD Q - * n 3 QrD j,< rD
o- Q _ rD Q
n d
rD fl
o
o° O o a,
Q
rD
Ln
www.boschsecurity.com ; ;;1 BOSCH
Invented for life
The cellular communicator enables secure two-way IP
communication over the Verizon 4G LTE cellular
network by plugging into a compatible control panel or
communicator interface.
Typical applications are:
Alarm reporting to a central station
Remote control panel programming through Remote
Programming Software with supported control panels
Remote monitoring and control through a mobile
application with supported control panels
Personal notification using SMS for compatible
control panels
Notice
Ce lular capability requires an Installer Services
account and appropriate data plan.
0
Secure Conettix IP communication from compatible
Bosch panels to Bosch receivers using Verizon 4G
LTE cellular network
Remote programming and monitoring of compatible
Bosch panels
Personal SMS message and e-mail notification
options
Direct configuration from Bosch Remote
Programming Software (RPS) eliminating the need
for separate configuration
Simple LED status information and advanced keypad
diagnostics available with easy 2 step plug-in
installation, troubleshooting, and maintenance
tBOS CH
3
a
Callout - - Description
1 - Cellular communicator
2 -Compatible control panel
3 - Antenna cable
4 - - Magnetic base antenna
Callout — Description
7 - - Remote PC's network
connection
8 - - Remote PC running RPS
9 - - Personal SMS notification
10 - -Ethernet connection